Remote Inspection Technician (5 month FTC)

Key responsibilities and competencies required for the role include but are not limited to as outlined below, the Remote Inspection Technician will be required to fulfil other duties as required to meet the needs of Oceaneering, and any other company within Oceaneering’s portfolio:

Essential

• Ensure that the workspace used to carry out remote visual inspection is a suitable environment, away from distractions and the relevant procedure for working with display screen equipment is being followed.
• Review the work pack provided by Oceaneering and/or the client to understand the scopes and raise any questions or issues to enough detail to progress the scope.
• Be able to read structural drawings, P&IDs, line drawn pipe work ISO’s to allow identification of equipment.
• Communicate to Oceaneering if there are any issues that could prevent/ delay the timely delivery of the scope.
• Ensure all relevant administrative tasks are completed on time. This specifically includes time sheets/time writing, daily reports, and inspection reports.
• Liaise with the client’s appointed representative to ensure that the work scope is clearly understood and is being carried out to the client’s satisfaction. Keep the client representative informed of progress or delays, forthcoming activities and any other relevant information.
• Carry out remote visual inspections to allow defect identification for assessment by Engineers.
• Be able to give feedback on work scopes & systems used to allow continuous improvement.
• Complete activities in an independent and impartial manner at all times and if any concerns then report these to Technical Manager and QHSE Manager

Health Safety & Environment Responsibilities

• Participate in all relevant company safety procedures and pre-job planning, including toolbox talks and risk assessments.
• Report any hazardous defects in plant, equipment and workplace, or shortcomings in the existing controls, to a responsible person without delay
• Work in a safe manner and ensure any task has been risk assessed prior to commencing work
• Report any incident, near miss or positive performance in accordance with company or client
• procedure
• Co-operate with any safety audits being conducted.
• Ensure company equipment is appropriately managed and maintained on site
• Ensure that all work complies with the company and contract QHSE policies and procedures as appropriate
• Operate and act responsibly, taking into account the need to progress environmental and social outcomes simultaneously.
• Participate in incident investigations identifying preventive and corrective actions, where requested.
• Attend HSE meetings, toolbox talks, and other relevant meetings as required, and actively contribute wherever possible.

Safety

• Ensure that the Safety policies and procedures are understood and adhered to so far as is reasonably practicable in order to ensure a safe working environment.

Other

• Carry out work in accordance with the Company Health, Safety, Environmental and Quality Systems.
• Perform the assigned tasks with due diligence regarding the Integrated Management Systems on the Company.
• Eliminate waste of whatever form, to suggest the use of more environmentally friendly substances and practices and contribute to the continuous improvement of the environment.

Supervisory Responsibilities

• This position has NO direct supervisory responsibilities.

Required

• Vocational qualifications in Inspection, Engineering or Technical disciplines
• Five years relevant experience (preferred) in NDT, Inspection of offshore plant and equipment (recognised Inspection/NDT qualifications, Technician under Institute of NDT etc).
• Familiar with requirements of ISO/IEC 17020:2012
• Ability to demonstrate a good all-round skills capability in the following areas:
  • Negotiating skills
  • Compliance issues (Quality, Health & Safety, Environment)
  • Communication
  • Interpersonal
  • Working on own initiative
  • Achieving targets and work prioritisation
  • Computer applications
  • Time management
  • Teamwork and cooperation
  • Problem solving
  • Continuing professional development

Desired

• Working towards further or higher education qualification in an engineering or technical discipline, e.g., HNC/HND/BSc
• API 510/570/579, ASME I/II code certification
• UKAS RG2 Cat 4
• Knowledge of HDR/Point Cloud                                      

Knowledge, Skills, Abilities, and Other Characteristics

• Excellent organisation and interpersonal skills
• Good knowledge and use of Microsoft Office
• Good knowledge and use of SharePoint
• Must be familiar with QA/QC systems and procedures, service quality and customer satisfaction
• Ability to priorities workload effectively
• Gives and receives constructive feedback

How to Apply:

We offer a competitive salary, a comprehensive benefits package and the opportunity to advance in an international company. To apply, click 'Apply Now'.